Bnc SAM 935 Portable Gamma Spectroscopy System Manual de usuario Pagina 36
- Pagina / 70
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
32 SAM 935™ Instruction Manual
•CAPTURE (F3) saves the currently displayed reading. The current alarm will be terminated when
you press C
APTURE. If the condition continues to alarm, a new alarm will be created and you will
again have the choice to capture it or not.
•S
ILENCE (F4) turns off the audible alarm. If there are no alarms currently going on, then the F4
function key becomes A
LM TEST. Pressing ALM TEST will activate the alarm indicators for test pur-
poses; each press of the A
LM TEST key will cause the alarm indicators to turn on for 5 seconds.
• When in the alarm review mode, the F2, F3, and F4 function keys become R
ETURN, PRN SEL, and
MCA, respectively. These functions are described above in Section 4.5.
5.3 The Detail Mode of Operation
In Detail mode, the actual spectrum being acquired is displayed. If an alarm is in progress, the displayed
spectrum is the accumulated spectrum for the entire alarm:
The function keys on the detail display are:
•S
URVEIL (F1) will switch to the Surveillance mode of operation.
•C
ALIB (F2) performs the quick, one-button calibration adjustment that is described in Section 4.2.1
and in the Quick Reference.
•C
APTURE (F3) saves the currently displayed reading. The current alarm will be terminated when
you press C
APTURE. If the condition continues to alarm, a new alarm will be created and you will
again have the choice to capture it or not.
•S
ILENCE (F4) turns off the audible alarm. If there are no alarms currently going on, then the F4
function key becomes A
LM TEST. Pressing ALM TEST will activate the alarm indicators for test pur-
poses; each press of the A
LM TEST key will cause the alarm indicators to turn on for 5 seconds.
• When in the alarm review mode, the F2, F3, and F4 function keys become R
ETURN, PRN SEL, and
MCA, respectively. These functions are described above in Section 4.5.
5.4 Manual Mode
Manual mode is a sophisticated, alternate mode of operating the SAM 935. Use this mode to acquire data;
view and edit hardware parameters; set, clear, and edit regions of interest (ROIs); and perform qualitative
analyses.
1. Press the U
TIL button and choose
Manual Mode
from
the Utilities menu
- Instruction Manual 1
- WARRANTY 2
- Table of Contents 3
- 2 SAM 935™ Instruction Manual 4
- 1. Introduction 5
- 1.2 Quick Reference 7
- 4 SAM 935™ Instruction Manual 8
- SAM 935™ Instruction Manual 5 9
- 2. Connecting Hardware 10
- SAM 935™ Instruction Manual 7 11
- 3. Configuring the SAM 935 12
- SAM 935™ Instruction Manual 9 13
- 3.2 Recalibration Procedure 14
- TIL key 15
- ES (F3) the first 15
- Acquire Background 16
- Calibrate Area Monitor 16
- Utilities 16
- Adjustment Complete 16
- 3.2.3 Fine Energy Calibration 18
- TART (F2) 19
- CCEPT (F4) 19
- ULL and P-SHORT keys 20
- Analysis Tools 21
- Area Monitor Setup 22
- Select Dose Rate Units 22
- Select Dose Rate Trigger 22
- 3.4 Dose Rate Calibration 23
- 4. Operating the SAM 935 24
- DJUST (F3) button 26
- 4.3 Powering the SAM 935 Off 27
- 4.5 Reviewing Alarms 29
- 4.6 The SAM 935 Interface 30
- 4.6.2 Function Keys 31
- 4.6.4 Editing Instructions 31
- Editing Text 32
- Editing Numbers 32
- 4.6.5 The Utilities Screen 33
- 5. SAM 935 Modes of Operation 34
- 5.4 Manual Mode 36
- Section 5.4.3 37
- 5.4.1 MCA Presets 38
- 5.4.3 Manual Mode Utilities 40
- 5.5 Background Mode 41
- 5.6 Calibration Mode 42
- 5.6.2 Fine Energy Calibration 43
- 6. Utilities 44
- 6.1 Area Monitor Setup 45
- 6.1.2 Select Triggers 46
- Set Default Trigger 47
- 6.1.4 Preventing False Alarms 48
- 6.1.5 Calibrate Dose Rate 49
- NTER to save the new value 50
- 6.2 Clear Stored Alarms 51
- 6.3 Edit Isotopes 51
- 6.3.1 Adding a New Isotope 52
- 6.3.2 Enable/Disable Isotopes 52
- 6.3.3 Editing an Isotope 52
- 6.4 Edit Isotope Radiations 53
- 6.5 Print Databases 53
- 6.6.1 Adding a Standard 54
- 6.6.2 Deleting a Standard 54
- 6.6.3 Editing a Standard 54
- 6.7 Select / Edit Detector 55
- 6.8 Analysis Tools Setup 56
- 6.10 Show System Information 57
- 6.11 Set Serial Speed 58
- 6.12 Set Report Title String 58
- 6.14 Set Backlight Delay Time 59
- 6.15 Print Stored Spectra 59
- 6.16 Clear Stored Spectra 59
- 6.17 Switch to Remote 60
- 6.18 Clear ALL Data and Reset 60
- 7. Reports 61
- 7.3 Energy Calibration Report 62
- 7.4 Manual MCA Report 63
- 7.5 Database Reports 64
- 8. Specifications 65
- Appendix A: AutoLoad 67
Relacionado con productos y manuales para Instrumentos de medición Bnc SAM 935 Portable Gamma Spectroscopy System
(177 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.016 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales