Bnc 1105 Universal Counter Manual de usuario Pagina 84
- Pagina / 197
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
84
8484
84
will disappear from the display as calibration is done. On the
contrary, the NG message will show on the display as calibration is
failed.
6.7 How to do the ATT x 10 Gain Calibration via CH1
The Offset Calibration via CH1 is for checking ATT x 10 and DC +9V.
Please do the following procedures to finish the calibration.
1. Press UTILITY > CAL > Enter Security Code > Cal Diag > Gain
Att1.
2. Use the BNC T-connector with 2 BNC cords to link an Agilent
33220A and a DMM (multimeter).
3. Under the Agilent 33220A operation, the procedures should be
Utility > DC ON > Output Setup > Hi-Z.
4. Adjust the voltage on the Agilent 33220A, and let the DMM
displays +5.000V ±0.001V.
5. Remove the input source, from the DMM, on the counter.
6. Press the softkey under RunCal to do the calibration. Then, the
counter’s display will show “Calibrating…”. The finished message
will disappear from the display as calibration is done. On the
contrary, the NG message will show on the display as calibration is
failed.
6.8 How to do the ATT x 10 Gain Calibration via CH2
The Offset Calibration via CH2 is for checking ATT x 10 and DC +9V.
Please do the following procedures to finish the calibration.
1. Press UTILITY > CAL > Enter Security Code > Cal Diag > Gain
Att2.
2. Use the BNC T-connector with 2 BNC cords to link an Agilent
33220A and a DMM (multimeter).
3. Under Agilent 33220A operation, the procedures should be Utility
> DC ON > Output Setup > Hi-Z.
- MODEL 1105 1
- 400 MHz Universal Counter 1
- Table of Contents 2
- General Information 5
- 1.2 Warranty Information 6
- Limitation of warranty 7
- 1.3 Precaution of Operation 7
- 1.4 Upkeep of the MODEL 1105 8
- 1.5 Safety Information 8
- 1.6 Symbols and Terms 9
- 1.7 Inspection 10
- 1.8 Options and Accessories 11
- Overview 12
- 2.1.2 To Replace the Fuse 14
- 2.2.1 The Front Panel 18
- 2.2.2 The Rear Panel 20
- Making Measurements 22
- 3.3 Time Interval Measurement 24
- 3.4 Period Measurement 25
- 3.6 Pulse Width Measurement 28
- 3.7 Duty Cycle Measurement 29
- 3.8 Totalize Measurements 31
- 3.9 Phase Measurements 32
- Front Panel Operations 35
- 4.2 Key Functions 36
- Stop/Single) 37
- Auto Arming 38
- Digits Arming 40
- 4.4 Setting Scale and Offset 46
- is then 47
- 4.5 Limits Operations 48
- 4.6 Statistics Operations 50
- 4.8 Trigger Setting 52
- 4.10 Utility Operations 58
- :CALibration:SECurity:STATe 59
- <Boolean>,<NRf> 59
- 4.11 Display Tips 61
- 4.11.2 Get HELP on ANY KEY 62
- Technical Support 63
- Remote Interface Operations 65
- :AUTO<Boolean> 74
- :CONTinuous<Boolean> 74
- [:IMMediate] 74
- The [:SENSe] command 75
- The :TRACe Commands 76
- Commands SYSTEM-RELATED 78
- Manual Calibration Procedures 81
- (Including External ARM) 85
- Error Messages 88
- 7.2 Execution Errors 91
- 7.3 Device-Specific Errors 92
- 7.4 Query Errors 92
- 7.5 Counter-Specific Errors 93
- Appendix 94
- Internal vs. External Time 96
- Base Selection 96
- A.1 RMS Resolution 99
- C. General Specifications 101
- D.2 Command Reference 106
- The command :CALCulate2 109
- The Command :CONFigure 120
- The Commands :MEASure? 129
- The Command :SENSe 136
- The Commands :SYSTem 152
- The Commands :TRACe 156
- Example 4 Other Measurement 182
- Example 5 Scale & Offset 185
- Example 6 Limit Modes 189
- Example 7 Stats Modes 193
Relacionado con productos y manuales para Instrumentos de medición Bnc 1105 Universal Counter
Instrumentos de medición Bnc Key Chain Radiation Detector for Upper-Range Radia Manual de usuario
(4 paginas)
(4 paginas)
Instrumentos de medición Bnc 1621M Manual de usuario
(27 paginas)
(27 paginas)
Instrumentos de medición Bnc 1703M Manual de usuario
(14 paginas)
(14 paginas)
Sealife Flashes de las cámaras manuales de usuario
La lista de productos de Sealife Flashes de las cámaras contiene 11 manuales de usuario para 4 seleccionados. Todas las guías de usuario en pdf están disponibles para descargar o ver en línea.
Comentarios a estos manuales