Bnc 1105 Universal Counter Manual de usuario Pagina 97
- Pagina / 197
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
97
9797
97
Channel
1 and 2
Trigger Default setting is Auto Trigger at 50 %
“Auto” Gate Time 0.1 sec
STD CH 3 375 MHz to 6 GHz (0.166 ns to 2.6 ns)
Frequency Ratio
CH 1/ CH 2, CH 1/ CH 3, CH 2/ CH 1, CH 3/ CH1
(Measurement is specified over the full signal range of each input.)
Results Range 10E-10 to 10E+11
“Auto” Gate Time 0.1 sec
Time Interval
Measurement is specified over the full signal ranges of Channels 1 and 2. The width of the
pulse must be greater than 1 ns, frequency range to 300 MHz.
Trigger Default setting is Auto Trigger at 50 %
Results Range -0.5 ns to 10E+5 s
Resolution 40 ps
RMS Resolution 120 ps
Systematic
Uncertainty
(TI × Time Base Error) ± Trigger Level Timing Error ± 500 ps Differential Channel Error
Pulse Width Time
Measurement is specified over the full signal range of Channel 1. The width of the pulse
must be greater than 1 ns frequency range to 300 MHz).
Pulse Selection Positive or Negative
Trigger Default setting is Auto Trigger at 50%
Results Range 1.5 ns to 10E+5 s
Resolution 40 ps
RMS Resolution 120 ps
Systematic
Uncertainty
(Pulse Width Time x Time Base Error) ± Trigger Level Timing Error ±
500 ps Differential
Channel Error.
Rise/Fall Time
Measurement is specified over the full signal range of Channel 1. The width of the pulse
must be greater than 1 ns frequency range to 300 MHz).
Edge Selection Positive or Negative
Trigger Default setting is Auto Trigger at 10% and 90%
Results Range 2 ns to 10E+5 s
Resolution 40 ps
RMS Resolution 120 ps
Systematic
Uncertainty
(Edge Time x Time Base Error) ± Trigger Level Timing Error ± 500 ps Differential
Channel Error
Phase
Measurement is specified over the full signal range of each input.
The width of the pulse
must be greater than 1 ns, frequency range to 300 MHz
Results Range -180° to +360°
Resolution 40 ps
RMS Resolution 120 ps
Systematic
Uncertainty
± (Trigger Level Timing Error) ×Frequency
Duty Cycle
Measurement is specified over the full signal range of Channel 1.
The width of the pulse
must be greater than 1 ns, frequency range to 300 MHz
Pulse Selection Positive or Negative
Trigger Default setting is Auto Trigger at 50 %
Results Range 0 to 1
Resolution 40 ps
RMS Resolution 120 ps
Systematic
Uncertainty
± Trigger Level Timing Error ± 500 ps Differential Channel Error
Totalize
Measurement is specified over the full signal range of Channel 1.
The width of the pulse
must be greater than 1 ns, frequency range to 400 MHz
Pulse Selection Positive or Negative
- MODEL 1105 1
- 400 MHz Universal Counter 1
- Table of Contents 2
- General Information 5
- 1.2 Warranty Information 6
- Limitation of warranty 7
- 1.3 Precaution of Operation 7
- 1.4 Upkeep of the MODEL 1105 8
- 1.5 Safety Information 8
- 1.6 Symbols and Terms 9
- 1.7 Inspection 10
- 1.8 Options and Accessories 11
- Overview 12
- 2.1.2 To Replace the Fuse 14
- 2.2.1 The Front Panel 18
- 2.2.2 The Rear Panel 20
- Making Measurements 22
- 3.3 Time Interval Measurement 24
- 3.4 Period Measurement 25
- 3.6 Pulse Width Measurement 28
- 3.7 Duty Cycle Measurement 29
- 3.8 Totalize Measurements 31
- 3.9 Phase Measurements 32
- Front Panel Operations 35
- 4.2 Key Functions 36
- Stop/Single) 37
- Auto Arming 38
- Digits Arming 40
- 4.4 Setting Scale and Offset 46
- is then 47
- 4.5 Limits Operations 48
- 4.6 Statistics Operations 50
- 4.8 Trigger Setting 52
- 4.10 Utility Operations 58
- :CALibration:SECurity:STATe 59
- <Boolean>,<NRf> 59
- 4.11 Display Tips 61
- 4.11.2 Get HELP on ANY KEY 62
- Technical Support 63
- Remote Interface Operations 65
- :AUTO<Boolean> 74
- :CONTinuous<Boolean> 74
- [:IMMediate] 74
- The [:SENSe] command 75
- The :TRACe Commands 76
- Commands SYSTEM-RELATED 78
- Manual Calibration Procedures 81
- (Including External ARM) 85
- Error Messages 88
- 7.2 Execution Errors 91
- 7.3 Device-Specific Errors 92
- 7.4 Query Errors 92
- 7.5 Counter-Specific Errors 93
- Appendix 94
- Internal vs. External Time 96
- Base Selection 96
- A.1 RMS Resolution 99
- C. General Specifications 101
- D.2 Command Reference 106
- The command :CALCulate2 109
- The Command :CONFigure 120
- The Commands :MEASure? 129
- The Command :SENSe 136
- The Commands :SYSTem 152
- The Commands :TRACe 156
- Example 4 Other Measurement 182
- Example 5 Scale & Offset 185
- Example 6 Limit Modes 189
- Example 7 Stats Modes 193
Relacionado con productos y manuales para Instrumentos de medición Bnc 1105 Universal Counter
Instrumentos de medición Bnc Key Chain Radiation Detector for Upper-Range Radia Manual de usuario
(4 paginas)
(4 paginas)
Instrumentos de medición Bnc 1621M Manual de usuario
(27 paginas)
(27 paginas)
Instrumentos de medición Bnc 1703M Manual de usuario
(14 paginas)
(14 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales